©2006 Bobsrepairs.com™, Inc. All rights reserved.
Low Rates - Fast Prompt Service - Guaranteed Work - All Makes, All Models - Repairs done on premise
ADMIRAL
Range/Stove/Oven Fault Codes
Failure
Code Condition Check/Repair
F1 Defective touch pad or membrane Replace touch pad or clock assembly (also called the ERC) (usually the touch pad)
F1 Watchdog on board Replace touch pad or clock assembly (also called the ERC)
F2 Oven too hot Replace relay board (if present) or oven temperature sensor
F3 or F4 Open or shorted oven temperature sensor Replace oven temperature sensor
F5 Hardware and watchdog circuits disagree Replace clock assembly (also called the ERC)
F6 Missing AC signal Check for proper voltage
F7 Function key shorted or stuck button Replace touch pad or clock assembly (also called the ERC) or un-stick button
F8 Analog/Digital trouble Replace clock assembly (also called the ERC)
F9 Door latch trouble Check door lock circuit or replace clock assembly (also called the ERC)
F0 Function key stuck Replace touch pad or clock assembly (also called the ERC)
AMANA
Range/Stove/Oven Fault Codes
Failure Code - glass link Electronic Range Control (ERC) Condition Check/Repair
Door flashing #0, 1, 2, 3 Latch switch broken Replace
Lock flashing Latch switch broken Replace
F0 Loss of safety signal Replace adapter board
F1 Watchdog circuit Replace Electronic Range Control (ERC)
F2 Oven too hot Replace oven temperature sensor
F3 F4 Open or shorted oven temperature sensor Replace oven temperature sensor
F7 Shorted touch panel Replace glass panel
F9 Motorized door Check latch
FF Lock error Check switch and motor
Electronic Range Control (ERC) III / Relay board with separate board / push buttons
F0 Shorted push pad Replace
F1 Failed Electronic Range Control (ERC) Replace
F2 Oven too hot Replace oven temperature sensor
F3 F4 Shorted or open oven temperature sensor Replace oven temperature sensor
F5, F6, F8 Failed Electronic Range Control (ERC) Replace ERC
F7 Shorted or sticking button Check glass alignment, replace touch panel if necessary
F9 Door latch failure Replace door latch switch or assembly if necessary
AMANA
Dual Convection Wall Oven
Failure Code Condition Check/Repair
F0 Shorted touch pad Replace touch pad
F1 Electronic range control failure Replace electronic range control (ERC)
F2 Oven temperature 100 degrees over limit Replace oven temperature sensor
F3 Shorted oven temperature sensor Replace oven temperature sensor
F4 Open oven temperature sensor Replace oven temperature sensor
F6 Electronic range control component failure Replace electronic range control (ERC)
F7 Failure detected in self-clean lock circuitry Check door latch mechanism
AMANA
"Big Oven" 5.1 cubic ft. (Sigma Touchmatic ERC)
Failure Code Condition Check/Repair
F0-0 No Error Initial factory setting
F1-1 Over temperature while cooking Check oven temperature sensor and wiring first, replace control board if oven temperature sensor is good
F1-3 Over temperature while cleaning Check oven temperature sensor and wiring first, replace control board if oven temperature sensor is good
F1-5 Cancel key input out of range Replace control board
F1-7 Keyboard disconnected Verify wire connection is tight.Replace control if failed
F1-8 Shorted key Replace control board
F1-9 Slave micro not functioning Replace control board
F1-A Circuit board grounding Replace control board
F1-C Control not calibrated Replace control board
F1-E Circuit board data corruption Replace control board
F1-F Circuit board data corruption Replace control board
F1-H Door switch input circuit failure Check switch and wiring
F1-J Latch switch input circuit failure Check switch and wiring
F3-1 Oven temperature sensor or oven temperature sensor circuit failure Check wire connections and oven temperature sensor
F9-1 Auto latch will not lock Check wiring, motor, and latch switch
F9-2 Auto latch will not unlock Check wiring, motor, and latch switch
Asko
Dishwasher
Failure
Code Condition Check/Repair
F1 Water heating fault, selected temperature not reached within 60 minutes · Incoming water temperature too cool
· Heating element burned out
· Thermostat defective
F2 High water level · Plugged/Bad water pump
· Defective water inlet valve
F3 Thermistor fault · Open thermistor
· Bad wiring to thermistor
F4 Fault with water fill (only on machines with level-controlled fill)
Note: Lights blinking, pump running and controls dead indicates an over fill fault 1. Disconnect the power to the unit
- Remove the lower access panels and check the tray under the dishwasher (you will probably find it is full of water)
- Use a towel or a sponge to remove the water
- There is a float that should stop the operation of the dishwasher and run the pump if water is in this tray. Check this pump to see if it is functional
- Test the dishwasher
- If there are no leaks from the dishwasher into the pan, check the drain hose under the sink
- THE DRAIN HOSE MUST RUN UP TO THE TOP OF THE UNDERSIDE OF THE COUNTERTOP THEN DOWN TO THE DRAIN. (If the hose is not set up like this, water from the sink drain will flow into the dishwasher and overfill the tray
*Faults may vary by model. Use this as a general guide.
Asko
Dryer
Failure
Code Condition Check/Repair
F1 Condensate drain overfilling Check condensate reservoir pump and drain tube.
F2 Maximum drying time exceeded (3hrs) · Check for tripped circuit breaker or blown fuse
· Check ductwork for lint build-up
· Check hi-limit and cycling thermostat
· Check heating element
F3 Thermistor fault · Open thermistor, replace
· Bad wiring to thermistor
F4 Too much lint in the lint filter, front housing, or in the condenser Clean lint from lint filter and/or condenser
F5 Fault in the moisture sensor · Lint covering sensor in front of housing
· Bad sensor
· Bad wiring to sensor
Asko
Washing Machine
Failure
Code Condition Check/Repair
F1 Water supply/low water fill · Check water supply to machine
·Replace water inlet valve
F2 Water level too high · Plugged/Bad water pump
· Faulty water valve
F3 Pump problem Check pump trap and clean.
F4 Thermistor problem · Open thermistor, replace
· Bad wiring to thermistor
F5 Fault in thermal cutout or heating pause fault. Selected temperature not reached in 90 minutes · Check heating element
· Check thermostat
F6 Motor fault · Check wiring to motor
· Replace motor if necessary
F7 Door lock release fault · Bent pull-rod for door latch
· Bad door latch solenoid
00 00 Machine did not spin Check load for out of balance Redistribute load and restart
CALORIC
Range/Stove/Oven Fault Codes
Failure Code - glass link Electronic Range Control (ERC) Condition Check/Repair
Door flashing #0, 1, 2, 3 Latch switch broken Replace switch
"Lock" flashing Latch switch broken Replace switch
F0 Loss of safety signal Replace adapter board
F1 Watchdog circuit Replace Electronic Range Control (ERC)
F2 Oven too hot Check oven temperature sensor
F3 F4 Open or shorted oven temperature sensor Replace oven temperature sensor
F7 Shorted touch panel Replace touch panel
F9 Motorized door problem Check door latch
FF Door lock error Check door switch and latch motor
Electronic Range Control (ERC) III / Relay board with separate board / push buttons
F0 Shorted touch pad Replace touch pad
F1 Failed Electronic Range Control (ERC) Replace ERC
F2 Oven too hot Check oven temperature sensor, replace if necessary
F3 F4 Shorted or open oven temperature sensor Replace oven temperature sensor
F5, F6, F8 Failed Electronic Range Control (ERC) Replace ERC
F7 Shorted or sticking button Check glass touch panel alignment, replace if necessary
F9 Door latch failure Replace door latch if necessary
CALORIC
RST376 Gas Range Fault Codes
Failure
Code Condition Check/Repair
F1 Clock bad Replace clock assembly (also called the ERC)
F2 Oven temperature sensor defective Replace oven temperature sensor
F3 Open oven temperature sensor Replace oven temperature sensor
F4 Oven temperature sensor low rating Replace oven temperature sensor
F5 Clock failure Replace clock assembly (also called the ERC)
F6 Power surge (clock) Try turning off power to appliance for one minute. If problem persists, replace clock assembly (also called the ERC)
F7 Touch panel button stuck Replace touch panel (membrane)
F8 Failure of diagnostic read-out Replace clock assembly (also called the ERC)
DACOR
Range/Stove/Oven Fault Codes
Failure
Code Condition Check/Repair
F0 Clock pushbutton is stuck in a depressed position Check clock buttons
F1 Element relay circuit failure Control board may be bad
F2 Oven temperature exceeded the clean runaway temperature (self clean only) or the cooking runaway temperature (cooking modes only) Call for service
F3 Short Circuit in the oven temperature sensor Check oven temperature sensor for continuity, if no resistance (zero ohms), replace
F4 Short Circuit in the oven temperature sensor Check oven temperature sensor for continuity, if no resistance (zero ohms), replace
F6 Failure in the EEPROM check comparison (only time of day and timer will operate) Call for service, electronic clock control is usually the cause of the problem
F7 Failure of the self- clean automatic door latch system Check door latch and switch(es)
F8 Failure of the door latch motor. Occurs when the motor runs for two minutes without the door locking in self-clean mode Check door lock motor and door latch
FRIGIDAIRE
Range/Stove/Oven Fault Codes Version 1
Failure
Code Condition Check/Repair
F2 Oven temp is above design specifications Oven temp has risen above 665F and door unlocked or above 965F with door locked. Check oven temperature sensor.
F3 The oven temperature sensor is open Check for open wire connection between EOC (Electronic Oven Control - Clock) and the oven temperature sensor. Replace sensor if no wiring problem.
F4 The oven temperature sensor is shorted Check for shorted wire and/or connections between the EOC (Electronic Oven Control - Clock) and the oven temperature sensor. Replace sensor if no wiring problem.
F5 The watchdog is active when it should be off Microprocessor checking the operation of the EDC relay, after selection of bake, broil, or clean operation. Relay failed this check.
F6 No 60 Hz time base 60 Hz time base is required for time controlled cycling. Replace EDC.
F7 Lock motor relay watchdog circuit is active when it should be off Microprocessor checking the operation of the EDC lock, relay failed. Replace EDC.
F8 Lock motor relay watchdog is active when it should be off Microprocessor checking the operation of the EDC lock relay after self clean is selected, relay failed. Replace EDC.
FRIGIDAIRE
Range/Stove/Oven Fault Codes Version 2
Failure
Code Condition Check/Repair
F0 & F1 EOC (Electronic Oven Control) failure Replace
F2 Oven too hot Check Bake function
F3 Oven temperature sensor open Check oven temperature sensor, 1100 ohms
F4 Oven temperature sensor shorted Replace component
F5, 6, 7 EOC (Electronic Oven Control) failure Replace component
F8 Lock switches Check or Replace component
FRIGIDAIRE
Range/Stove/Oven Fault Codes Version 3
Failure
Code Condition Check/Repair
F0 & F1 EOC (Electronic Oven Control) failure Replace EOC (Electronic Oven Control)
F2 Oven too hot Likely a bad oven temperature sensor (should read 1100 ohms) Possible bad EOC (Electronic Oven Control)
F3 Oven temperature sensor open Replace oven temperature sensor
F4 Oven temperature sensor shorted Replace oven temperature sensor
F5 or F6 or F7 EOC (Electronic Oven Control) failure Replace EOC(Electronic Oven Control)
FRIGIDAIRE
Range/Stove/Oven Fault Codes Version 4
Failure
Code Condition Check/Repair
F1 Circuit board defective Replace control board
F2 1. The oven temp has risen above 665F and the door is not locked or
- The temp has risen above 965F with the door locked 1. Check oven temp in mode that failure occurred. Replace EOC (Electronic Oven Control) if above limits
- Check 8-pin connector. Check and replace oven temperature sensor if necessary
F3 Oven temperature sensor is open (above 3000 ohms) Check resistance of oven temperature sensor, check for open wiring between oven temperature sensor and control
F4 Oven temperature sensor is shorted (below 500 ohms) Check resistance of oven temperature sensor, check for shorted wiring between oven temperature sensor and control
F5 Internal watchdog circuit has detected a failure Defective EOC (Electronic Oven Control)
F6 Shorted buttons Check push buttons and dome switches on control
F8 Logic interrupted (lock motor switch sequence) Check door lock switches and wiring
GE
Gas or Built In Oven Fault Codes
Failure
Code Condition Check/Repair
F0 or F1 Failed transistor in control If code cannot be cancelled, replace the Electronic Range Control (ERC) or touch pad
F2 Oven over temp - exceeded 590F with door in unlocked position or 990F with door locked If actual temp condition occurred, look for welded relay contacts or high resistance connection or any cause in the oven temperature sensor circuit
F3 Open oven temperature sensor circuit Measure oven temperature sensor circuit at oven temperature sensor (should be approx 1100 ohms at room temp); check for cut or pinched wire or loss of contact
F4 Shorted oven temperature sensor circuit Same as above; check for melted connector or both leads shorted to ground
F8 Component failure within Electronic Range Control (ERC) effecting temp processing circuits Replace Electronic Range Control (ERC)
F9 Problem with door lock circuit such as pinched wire between Electronic Range Control (ERC) and door lock switch Check wiring and test operation of switch
GE
XL44 Self Clean Oven Fault Codes
Failure
Code Condition Check/Repair
F0 - F1 - F7 Stuck keypad may mean relay is turned on. Determine if problem is with the Key Panel or Control by:
- Pushing CLEAR/OFF pad.
- Disconnecting Ribbon Cable from control and waiting at least 32 seconds to see if Code recurs. If code recurs, problem is in the control. Replace control.
If code does not recur, problem is with the Key Panel.
